Author: admin

INTRODUCTION

Rockmax Mesh is a fiberglass mesh use in waterproofing application. The mesh increases reinforced, tensile, adhesion and puncture resistance to waterproofing system.

TECHNICAL PROPERTIES

Color: White
Width x Length: 1 meter x 100 meter
Thickness: approx 0.22mm

PACKAGING

Roll: 1meter width x 100 meter length.

STORAGE

Storage in shade and dry condition at 10-30ºC. Avoid from sunlight, UV, frost, water, moisture and high temperature.

INTRODUCTION

Rockmax Epogard W1 is a two component, solvent free epoxy coating or lining. The cured material provides hard, gloss, smooth and watertight to concrete surfaces with and including abrasion and chemical resistance. It is suitable with potable or drinking water tank. The cured material is non-toxic.

APPLICATION AND INSTALLATION

PREPARATION

Concrete must be sound, clean and free from oil, grease, wax, cement paste, dust, dirt and any other contaminants. Concrete must be at least 28 days and minimum Compressive strength 25N/mm 2 and minimum tensile strength (pull off) at 1.5 N/mm 2 . The moisture content in concrete must be lower than 6%. The substrate should not have a relative humidity more than 85% at installation period. Total enclosed grinding, high water pressure jet, or scarifying must be employed followed by vacuuming. All holes and voids must be repaired prior to installation. Seal the surface with moisture barrier or modified epoxy cement in case of surface subject to rising damp or moisture movement. Please consult Rockmax for more information.

PRIMING

Apply Rockmax Epogard P by roller at one coat at approximate coverage rate 0.2 kg/m 2 . Allow the prime coat to dry approximate 4 hours. The difference type of primers must be considered according to substrate conditions.

MIXING

Stir base and hardener component separately approximate 10 second. Pour part A and part B together in the bucket and continue mixing for 3 minute until homogeneous. Avoid whipping air into the material. It is recommended that only full units to be used, that all components are thoroughly mixed. We do not recommend using partial kits and reduce or dilute materials.

APPLICATION

Applied Rockmax Epogard W1 by roller or stiff nylon type brush. Allow the first coat dry at approximate 5-6 hours (30ºC) and the second coat must be applied not more than 48 hours after the first coat application. When finished the application protect the coating from water.

PACKAGING

24kg set (A+B). Part A: 18kg and Part B: 6kg.

STORAGE

Storage in shade and dry condition. Avoid from frost, water, UV, moisture and high temperature.

INTRODUCTION

Rockmax Epogard T is a two component epoxy coal tar waterproofing. Cured material provides high chemical resistance, good abrasion and durability to concrete structures. It can protect concrete from chemical s, dilute acids, salt waters, high chlorine concentrate, alkalis, solvents.

APPLICATION AND INSTALLATION

PREPARATION

Concrete must be sound, clean and free from oil, grease, wax, cement paste, dust, dirt and any other contaminants. Concrete must be at least 28 days and minimum Compressive strength 25N/mm 2 and minimum tensile strength (pull off) at 1.5 N/mm 2 . The moisture content in concrete must be lower than 6%. The substrate should not have a relative humidity more than 85% at installation period. Total enclosed grinding, high water pressure jet, or scarifying must be employed followed by vacuuming. All holes and voids must be repaired prior to installation. Seal the surface with moisture barrier or modified epoxy cement in case of surface subject to rising damp or moisture movement. Please consult Rockmax for more information.

MIXING

Stir base and hardener component separately approximate 10 second. Pour part A and part B together in the bucket and continue mixing for 3 minute until homogeneous. Avoid whipping air into the material. It is recommended that only full units to be used, that all components are thoroughly mixed. We do not recommend using partial kits and reduce or dilute materials.

APPLICATION

Applied Rockmax Epogard T by roller or stiff nylon type brush. Allow the first coat dry at approximate 12 hours (30ºC) and the second coat must be applied not more than 48 hours after the first coat application. When finished the application protect the coating from water.

PACKAGING

24.50 kg set (A+B).
Part A: 21.0 kg and Part B: 3.50 kg.

STORAGE

Storage in shade and dry condition. Avoid from frost, water, UV, moisture and high temperature.

INTRODUCTION

Maxshield 400S is an atatic polypropylene plastomeric (APP) modified bitumen waterproof sheet membrane and can be used for exposed surface. It is formulated from high grade modified bitumen with selected elastic polymer and reinforced with non woven polyester reinforcement. The membrane provides good elongation, high puncture resistance and good mechanical characteristic. The membrane top surface finished with special grade material such as sand or slate which can be exposed to the environmental with no require protections.

APPLICATION AND INSTALLATION

PREPARATION

Concrete substrate must be at least 28 days old. Substrate must be sound, smooth, clean, dry and free from loose materials, oil, grease or any other contaminants. In case of substrate has moisture on surface use flame torch to dry up surface prior to apply primer.

PRIMING

Apply Maxshield Primer on prepared substrate at approximate coverage rate 5m2 per litre and allow to dry.

APPLICATION

Maxshield 400S should be install using gas torch. Slowly unrolled the membrane and flame torch the membrane until the bottom surface melt but do not over heat. Side overlap must be minimum 150mm. roll overlap joint must be minimum 100mm. Lap joint should be sealed by torch. All expansion joints, movement joints and all joints must be followed and allowed follow structural design. Other joints and end points must be allowed according to specifications. The membrane must be protected immediately after installation.

Maxshield 400S must be installed by experiences, trained and approved applicators. Installation shall be strictly in accordance with manufacture method statement instruction.

PACKAGING

Roll size: 1meter x 10meter.
Roll weight: approx 35kg.

INTRODUCTION

Maxshield 300S is an atatic polypropylene plastomeric (APP) modified bitumen waterproof sheet membrane. It is formulated from high grade modified bitumen with selected elastic polymer and reinforced with non woven polyester reinforcement. The membrane provides good elongation, high puncture resistance and good mechanical characteristic. The membrane is top coated by sand or polyethylene (PE) and bottom surface protected by heat sensitive film.

APPLICATION AND INSTALLATION

PREPARATION

Concrete substrate must be at least 28 days old. Substrate must be sound, smooth, clean, dry and free from loose materials, oil, grease or any other contaminants. In case of substrate has moisture on surface use flame torch to dry up surface prior to apply primer.

PRIMING

Apply Maxshield Primer on prepared substrate at approximate coverage rate 5m2 per litre and allow to dry.

APPLICATION

Maxshield 300S should be install using gas torch. Slowly unrolled the membrane and flame torch the membrane until the bottom surface melt but do not over heat. Side overlap must be minimum 150mm. roll overlap joint must be minimum 100mm. Lap joint should be sealed by torch. All expansion joints, movement joints and all joints must be followed and allowed follow structural design. Other joints and end points must be allowed according to specifications. The membrane must be protected immediately after installation.

Maxshield 300S must be installed by experiences, trained and approved applicators. Installation shall be strictly in accordance with manufacture method statement instruction.

PACKAGING

Roll size: 1meter x 10meter.
Roll weight: approx 30kg.

INTRODUCTION

Maxshield 150W is a cold applied self adhesive bituminous membranes. It is manufactured and formulated from modified SBS bitumen and high performance adhesive layer. This selected materials made very easy to installation. It is supplied in rolls 1meter width x 15meter long and 1.5mm thickness.

APPLICATION AND INSTALLATION

PREPARATION

Concrete substrate must be sound, smooth, clean, dry and free from loose materials, oil, grease or any other contaminants. In case of substrate has moisture on surface use flame torch to dry up surface prior to apply primer.

PRIMING

Apply Maxshield Primer on prepared substrate at approximate coverage rate 5m2 per litre and allow to dry.

APPLICATION

Maxshield 150W should be applied from lowest point. All joints, angles and end points must be overlap at minimum 75mm. Internal and external corners should be reinforced with 300mm membrane strip. End laps should be sealed. Ensure the membrane is perfectly stick and adhere with concrete substrate and no air pockets. It is recommended to protect the membrane by protection boards immediately. Do not exposed the membrane to direct UV for long period. Maxshield 150W must be installed by experiences, trained and approved applicators.

PACKAGING

Roll size: 1meter x 15meter.
Roll weight: approx 25kg.

INTRODUCTION

Rockmax Waterplug is quick setting cement mortar for stop water leakage. Use to stop water passage through concrete structure, concrete joint and rock foundation.

APPLICATION AND INSTALLATION

PREPARATION

Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles and cement paste. Ensure the surface is dry and free from water saturated.

MIXING

Mix Rockmax Waterplug with water at (water : waterplug = 1 : 5 by weight).

APPLICATION

Cut concrete substrate to receive V shape. Fill Rockmax Waterplug immediately after mixed. Wait for setting at 90 seconds. Remove all excess material on surface with and including leveling and making good surface.

PACKAGING

5Kg bag.

INTRODUCTION

Rockmax Roofgard is one part thixotropic dark brown bitumen emulsion cold applied liquid membrane. Use for general purpose waterproofing material. Good bonding many kind of substrate ie concrete, asbestos concrete, roof felt, timber, galvanized roof, metal and etc.

APPLICATION AND INSTALLATION

PREPARATION

Substrate must be sound, clean, free from oil, grease, mould oil, dust and loose particles. Ensure the surface is dry and free from water saturated.

PRIMING

Mixer must use low speed drill mixer (500 rpm) with and including good quality steel paddle. Make sure all tools and equipments are in good conditions and clean.

Dilute Rockmax Roofgard with water at 1 (Rockmax Roofgard) : 1 (water) by volume. Stir 2 part together approximate 1-3 minute until homogenius. Prime the surface by brush or roller at coverage rate 0.5kg/m2. Allow the prime coat to dry before top coat application.

APPLICATION

Apply first coat of Rockmax Roofgard to the primed surface by brush or roller. Allow first coat to dry approximate 60-90 minute. Apply second coat and allow to dry. For watertight apply 2-3 coats. Allow to completely dry for 4-6 hours prior to light traffic

CLEANING

Clean all tools and equipments immediately with kerosene or solvent.

PACKAGING

18Kg pail.

INTRODUCTION

Rockmax Ceramic V2 is a high performance waterborne acrylic binder with and including air encapsulated ceramic microspheres which provide excellent heat reflection. The benefits also include excellent waterproofing, cost saving and reduce temperature inside the building. By using the coating, customers can efficiently stabilize proc esses, protect personnel and maintain product levels. Its designed for both spray and roller coating method.

APPLICATION AND INSTALLATION

PREPARATION

Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles, cement past and. Ensure the surface is dry and free from standing water. The moisture content in concrete substrate must be check with limit not more than 5% moisture contents. If moisture contents in concrete higher than 5% Moisture Barrier must be apply. Check and investigate void, honeycomb, or crack on concrete substrate. All damaged must be repair prior to application. All joints and corner must be treated with Rockmax PUseal. Others substrate such as metal, steel should be consult Rockmax for more information.

PRIMING

Rockmax Ceramic V2 can dilute with water and apply as first prime coat (20% thin with water). Apply prime coat by brush or spray to the whole area.

APPLICATION

Mixer must use low speed drill mixer (500 rpm) with and including good quality steel paddle. Make sure all tools and equipments are in good conditions and clean. Stir Rockmax Ceramic V2 by mixer at approximate 30 second until see homogeneous. Apply First coat of Rockmax Ceramic V2 by roller. Allow the first coat to dry at 2 hours before next coat. Apply second and third coat to achieve design thickness (DFT). Follow first coat application.

Airless spray:
In case of spray method. Thin 10% with clean water for easy working properties.

CURING

Protect Rockmax Ceramic V2 by plastic sheet from rain and water. Rockmax Ceramic V2 is self curing and curing time is approximate 5-7 days prior to open to traffic.

PACKAGING

23Kg pail.

STORAGE

Storage in shade and dry condition. Avoid from frost, water, UV, moisture and high temperature.

INTRODUCTION

Rockmax Roofseal V1 is one component water based acrylic liquid waterproofing membrane. The special integral micro reinforcement improves tensile strength and increase durability of coating. The product provides high elasticity and good watertight to its structure.

APPLICATION AND INSTALLATION

PREPARATION

Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles and cement paste. Ensure the surface is dry and free from standing water. The moisture content in concrete substrate must be check with limited not more than 5% moisture contents. Investigate void, honeycomb, or crack on concrete substrate. All damaged must be repair prior to application. All joints and corner must be treated with Rockmax PUseal.

PRIMING

Apply one coat of dilute Rockmax Roofseal V1 with water at 1:1 ratio to prepared surface at approximate 0.2kg/m 2 per coat by roller. Allow the prime coat to dry at 1-3 hours prior to apply body coats.

APPLICATION

Mixer must use low speed drill mixer (500 rpm) with and including good quality steel paddle. Make sure all tools and equipments are in good conditions and clean. Stir Rockmax Roofseal V1 by mixer at approximate 1 minute until uniform homogeneous.

Apply First coat of Rockmax Roofseal V1 by roller with coverage rate at 0.30 kg per m 2 per coat. Allow the first coat to dry at 2-4 hours before next coat. Apply second and third coat to achieve 1mm total thickness (DFT). Follow first coat application method. Fiber mesh might be used between the first coat and second coat. The thickness of product depends on number of coats, application method, substrate quality and other factors related to application. In case of spray method, please consult Rockmax for more information.

PACKAGING

23Kg pail.

STORAGE

Storage in shade and dry condition. Avoid from frost, water, UV, moisture and high temperature.