ROCKMAX CERAMIC V2

ELASTOMERIC CERAMIC WATERPROOF COATING


INTRODUCTION

Rockmax Ceramic V2 is a high performance waterborne acrylic binder with and including air encapsulated ceramic microspheres which provide excellent heat reflection. The benefits also include excellent waterproofing, cost saving and reduce temperature inside the building. By using the coating, customers can efficiently stabilize proc esses, protect personnel and maintain product levels. Its designed for both spray and roller coating method.

AREA OF USES

Rockmax Ceramic V2 can used for the following flat exposed concrete roof, concrete gutter, steel gutter , façade , external concrete wall, roof metal sheet, steel tank , silos , electrical and mechanical room, area required control
temperature.

ADVANTAGES

  • Excellent heat reflective >80%.
  • Reduce temperature in building.
  • Excellent bonding.
  • Crack bridging ability.
  • Excellent elongation.
  • UV resistance.
  • Non yellowing.
  • Value engineering to building.
  • Reduce cost of air condition.
  • Reduce thermal shock.
  • Prevent rust and corrosion.
  • Long life span 10-15 years.
  • Easy application one part.
  • Can apply by spray.
  • Nice appearance.
  • APPLICATION AND INSTALLATION

    PREPARATION

    Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles, cement past and. Ensure the surface is dry and free from standing water. The moisture content in concrete substrate must be check with limit not more than 5% moisture contents. If moisture contents in concrete higher than 5% Moisture Barrier must be apply. Check and investigate void, honeycomb, or crack on concrete substrate. All damaged must be repair prior to application. All joints and corner must be treated with Rockmax PUseal. Others substrate such as metal, steel should be consult Rockmax for more information.

    PRIMING

    Rockmax Ceramic V2 can dilute with water and apply as first prime coat (20% thin with water). Apply prime coat by brush or spray to the whole area.

    APPLICATION

    Mixer must use low speed drill mixer (500 rpm) with and including good quality steel paddle. Make sure all tools and equipments are in good conditions and clean. Stir Rockmax Ceramic V2 by mixer at approximate 30 second until see homogeneous. Apply First coat of Rockmax Ceramic V2 by roller. Allow the first coat to dry at 2 hours before next coat. Apply second and third coat to achieve design thickness (DFT). Follow first coat application.

    Airless spray:
    In case of spray method. Thin 10% with clean water for easy working properties.

    CURING

    Protect Rockmax Ceramic V2 by plastic sheet from rain and water. Rockmax Ceramic V2 is self curing and curing time is approximate 5-7 days prior to open to traffic.

    PACKAGING

    23Kg pail.

    STORAGE

    Storage in shade and dry condition. Avoid from frost, water, UV, moisture and high temperature.

    ROCKMAX ROOFSEAL V1

    ELASTOMERIC ACRYLIC WATERPROOF



    INTRODUCTION

    Rockmax Roofseal V1 is one component water based acrylic liquid waterproofing membrane. The special integral micro reinforcement improves tensile strength and increase durability of coating. The product provides high elasticity and good watertight to its structure.

    AREA OF USES

  • Flat exposed concrete roof.
  • Concrete gutter.
  • Steel gutter.
  • Façade.
  • External wall cladding.
  • Metal Sheet roof.
  • External Wall.
  • ADVANTAGES

  • Excellent flexibility.
  • Excellent elongation.
  • Excellent adhesion.
  • Good tensile resistance.
  • Crack bridging ability.
  • UV resistance.
  • One part ready to use.
  • Durability.
  • Algae resistance.
  • Good puncture resistance.
  • Foot traffic.
  • Nice appearance.
  • APPLICATION AND INSTALLATION

    PREPARATION

    Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles and cement paste. Ensure the surface is dry and free from standing water. The moisture content in concrete substrate must be check with limited not more than 5% moisture contents. Investigate void, honeycomb, or crack on concrete substrate. All damaged must be repair prior to application. All joints and corner must be treated with Rockmax PUseal.

    PRIMING

    Apply one coat of dilute Rockmax Roofseal V1 with water at 1:1 ratio to prepared surface at approximate 0.2kg/m 2 per coat by roller. Allow the prime coat to dry at 1-3 hours prior to apply body coats.

    APPLICATION

    Mixer must use low speed drill mixer (500 rpm) with and including good quality steel paddle. Make sure all tools and equipments are in good conditions and clean. Stir Rockmax Roofseal V1 by mixer at approximate 1 minute until uniform homogeneous.

    Apply First coat of Rockmax Roofseal V1 by roller with coverage rate at 0.30 kg per m 2 per coat. Allow the first coat to dry at 2-4 hours before next coat. Apply second and third coat to achieve 1mm total thickness (DFT). Follow first coat application method. Fiber mesh might be used between the first coat and second coat. The thickness of product depends on number of coats, application method, substrate quality and other factors related to application. In case of spray method, please consult Rockmax for more information.

    PACKAGING

    23Kg pail.

    STORAGE

    Storage in shade and dry condition. Avoid from frost, water, UV, moisture and high temperature.

    ROCKMAX CRYSTALSEAL

    CRYSTALLIZATION WATERPROOF


    INTRODUCTION

    Rockmax Crystalseal is a crystallization waterproofing system based on cementitious slurry form. It consists of a selected silica aggregates, quartz sand, chemical additive and portland cement. Rockmax Crystalseal is full fill pore and capillary in concrete surface after chemical reaction develop. Rockmax Crystalseal withstand hydrostatic water pressure and permanent waterproofing system

    AREA OF USES

  • Water tank.
  • Water treatment tanks.
  • Reservoirs.
  • Tunnels.
  • Cement pipes.
  • Retaining walls.
  • Diaphragm walls.
  • Underground basements.
  • Foundations.
  • ADVANTAGES

  • Can apply negative and positive side.
  • Become integral part of structure.
  • Can apply on damp surface.
  • Seal minor cracks.
  • Economical.
  • Easy to apply by brush.
  • No need protection.
  • Non toxic.
  • Fast track project.
  • Wide range of applications.
  • APPLICATION AND INSTALLATION

    PREPARATION
    Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles and cement paste. Check and investigate void, honeycomb, or crack on concrete substrate. All damaged concrete must be repair prior to application. Saturated surface by spray water at least 2-3 hours prior application. No water standing on surface. Damp surface will allow chemical of Rockmax Crystalseal penetrate deeply into concrete.

    MIXING
    Mixer must use low speed drill mixer (500 rpm) with and including good quality steel paddle. Make sure all tools and equipments are in good conditions and clean. Add Rockmax Crystalseal (25kg bag) slowly into 7-8 litre of clean water. Mixing continueous approximate 3-5 minute until homogeneous. Do not add additional water to rework. It recommended to mix the whole set a time to achieve all mixture chemical in one bag.

    APPLICATION
    Apply Rockmax Crystalseal by plastic brush with approximate coverage rate 1-1.2kg/m2/coat. Two coat application is recommended. Allow 2-4 hours to dry between coats.

    Coverage rate: 1.0-1.2kg/m2/coat
    Number of coats: 2 coats

    CURING
    Allow Rockmax Crystalseal curing by spry clean water with approximate 2-3 days after dry and 3 times a day at minimum. Protect with plastic sheet to prevent drying up is prefer.

    PACKAGING

    25Kg bag.

    ROCKMAX HSC

    WATER BASED CRYSTALLIZATION WATERPROOF


    INTRODUCTION

    Rockmax HSC is a water based, chemical reaction, concrete and cement paste penetration to form a crystal matrix gel in pores, crack, void and capillaries below concrete surface. The solutions provide permanent concrete waterproof and increase concrete durability. The crystal matrix create a protection of cement paste from salt water, high contaminants water, sewage, waste water and some chemicals. Rockmax HSC will seal dead crack and hairline crack on concrete and remain active when contact with water

    AREA OF USES

  • Water tank.
  • Waste water tank.
  • Roof decks.
  • Car parks.
  • Highway and Bridge decks.
  • Marine structures.
  • Runway and Taxiway.
  • Precast concrete.
  • Concrete slab, deck, podiums
  • Concrete foundations and Pylons
  • ADVANTAGES

  • Protect from carbonation and chloride attack.
  • Penetrate to concrete surface
  • Fill porous and capillaries in concrete.
  • Permanent waterproof.
  • Increase durability of concrete.
  • Re active.
  • Vehicle trafficable.
  • Fast track project.
  • No de-bond as become part of concrete.
  • Easy to use.
  • One coat application.
  • Harden concrete surface.
  • APPLICATION AND INSTALLATION

    PREPARATION
    Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles and cement paste. Ensure the surface is dry and free from standing water. Concrete must be at least 4 weeks old. All damaged concrete surface must be repair by high quality modified concrete repair mortar prior to application. Construction joints, Expansion joints, Penetrations, Floor drain, Floor cover, Corner joints must be seal and treat with waterproofing material such as waterstop, waterproofing self adhesive tape and/or sealants. The waterproofing detail will be available upon request to Rockmax.

    APPLICATION

  • Apply Rockmax HSC by spray or roller at coverage rate at 4-5m2/litre.
  • Do not dilute the product with water or solvents.
  • After flooded Rockmax HSC to surface area wait until dry approximate 2-6 hours.
  • Immediately pour water on surface after product dry.
  • Curing by flood water 3 days after application.
  • Protection the curing area at least 24 hours prior to traffic.
  • CURING
    Curing by flood water to application area 3-4 times a days at minimum 3-5 days.

    PACKAGING

    20 litre pail.

    ROCKMAX PROOF H3

    POLYMER MODIFIED CEMENT WATERPROOF COATING


    INTRODUCTION

    Rockmax Proof H3 is a one component polymer modified cement based waterproof coating. Its provide excellent bonding and waterproofing to concrete substrate. Can use on portable water tank.

    AREA OF USES

    Rockmax Proof H3 can use as waterproof coating for basements, water tanks, waste water tanks, culverts, underground concrete structures, bathrooms, toilets, kitchens.

    ADVANTAGES

  • Good adhesion.
  • Waterproof concrete and mortar.
  • Easy application.
  • Can apply on damp surface.
  • Non toxic.
  • Chloride free.
  • Can apply on portable water tank.
  • Can apply on masonry.
  • Can apply on rough surface.
  •  

    PREPARATION AND APPLICATION

    PREPARATION

    Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles and cement paste. Ensure the surface is dry and free from water saturated. Check and investigate void, honeycomb, or crack on concrete substrate. All damaged must be repair prior to application. Special render mortar or special masonry must be check bond strength of Rockmax Proof H3 to ensure achieve the require strength. Saturated the surface with water at least 2-3 hours prior to application.

    MIXING

    Mixer must use low speed drill mixer (500 rpm) with and including good quality steel paddle. Make sure all tools and equipments are in good conditions and clean. Mix the material with clean water 5litre for 25kg bag of Rockmax Proof H3 . Mix for 3-4 minute until homogeneous and uniform.

    APPLICATION

    Apply Rockmax Proof H3 by plastic brush or roller on prepared surface with approximate 0.5-1.0mm per coat. Allow the first coat to dry approximate 2-4 hours and follow with second coat. Apply second coat in crossing direction with first coat. Allow second coat to dry at 2-3 hours. Make sure the surface dry up before spray water.

    PACKAGING

    25kg bag.

    STORAGE

    Storage in shade and dry condition. Avoid from frost, direct sunlight, water, moisture and high temperature.

    ROCKMAX PROOF H2

    FLEXIBLE CEMENTITIOUS WATERPROOF


    INTRODUCTION

    Rockmax Proof H2 is two components polymer modified flexible cementitious waterproof coating. The cured material provides good flexibility, waterproofin g and excellent adhesion to concrete and masonry substrate.

    AREA OF USES

  • Bathrooms and toilets.
  • Kitchens.
  • Swimming pools.
  • Ponds and fountains.
  • Wet areas.
  • Water tanks.
  • Underground walls.
  • Retaining walls.
  • Terraces and balconies
  • ADVANTAGES

  • Good flexibility.
  • Good elongation.
  • Good adhesion.
  • Easy application.
  • Pre-measure.
  • Can apply on damp surface.
  • Fast track project.
  • Can stick tile on top.
  • Non toxic
  • Can apply on masonry.
  • Can apply on rough surface.
  • APPLICATION AND INSTALLATION

    PREPARATION

    Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles and cement paste. Ensure the surface is dry and free from water saturated. Check and investigate void, honeycomb, or crack on concrete substrate. All damaged must be repair prior to application.

    Special render mortar or special masonry must be check bonding strength of Rockmax Proof H2 to ensure achieve the require strength. Saturated surface with water at least 2-3 hours prior to application.

    MIXING

    Mixer must use low speed drill mixer (500 rpm) with and including good quality steel paddle. Make sure all tools and equipments are in good conditions and clean. Add Rockmax Proof H2 part A(powder) into part B (Liquid) slowly while continue mixing. Mix approximate 3 to 5 minute until homogeneous. Do not add more water to rework.

    APPLICATION

    Apply Rockmax Proof H2 by plastic brush or roller on prepared surface with approximate 0.5-1.0mm per coat. Allow the first coat to dry approximate 2-4 hours and follow with second coat. Apply second coat in crossing direction with first coat. Allow second coat to dry at 2-3 hours. Make sure the surface dry up before spray water.

    PACKAGING

    25kg set.
    part A: 20 kg ; part B: 5 kg

    STORAGE

    Storage in shade and dry condition. Avoid from frost, direct sunlight, water, moisture and high temperature.

    ROCKMAX PROOF H1

    HIGHLY FLEXIBLE CEMENTITIOUS WATERPROOF


    INTRODUCTION

    Rockmax Proof H1 is a two component polymer modified highly flexible cementitious waterproofing system with excellent elongation and good adhesion to substrate especially for critical waterproofing area and under hydrostatic pressure area. The cured material provides waterproofing membrane and permanently waterproofing.

    AREA OF USES

  • Suspended swimming pools.
  • Super Structure waterproof.
  • Water tank, waste water tank.
  • Large water tank.
  • Suspended water tank.
  • Balcony.
  • Flat desk.
  • Critical waterproofing areas.
  • ADVANTAGES

  • Excellent flexibility.
  • Excellent elongation.
  • Excellent adhesion.
  • Easy application.
  • Can apply on damp surface.
  • Fast track project.
  • Can stick tile on top.
  • Can apply on masonry.
  • Can apply on rough surface.
  • APPLICATION AND INSTALLATION

    PREPARATION

    Concrete substrate must be sound, clean, free from oil, grease, mould oil, dust, loose particles and cement paste. Ensure the surface is dry and free from water saturated. Check and investigate void, honeycomb, or crack on concrete substrate. All damaged must be repair prior to application.

    Special render mortar or special masonry must be check bonding strength of Rockmax Proof H1 to ensure achieve the require strength.

    MIXING

    Mixer must use low speed drill mixer (500 rpm) with and including good quality steel paddle. Make sure all tools and equipments are in good conditions and clean.Add Rockmax Proof H1 part A (powder) into part B (Liquid) slowly while continue mixing. Mix approximate 3 to 5 minute until homogeneous. Do not add more water to rework.

    APPLICATION

    Apply Rockmax Proof H1 by plastic brush on prepared surface with approximate 0.5-1.0mm per coat. Allow the first coat to dry approximate 2-4 hours the start second coat. Apply second coat in crossing direction with first coat. Allow second coat to dry at 2-4 hours before start curing.

    CURING

    Allow Rockmax Proof H1 curing by spray clean water with approximate 2-3 days after dry. Keep Rockmax Proof H1 moist to prevent rapid drying up. Protect the area from damaged before finishing or tiling.

    PACKAGING

    36kg set.
    Part A: 18kg and Part B: 18kg

    STORAGE

    Storage in shade and dry condition. Avoid from frost, water, moisture and high temperature .